+1 (813) 551-9051
info@micomotorsports.com

Dyno

Skip to content
Home / Dyno
In-house Dynojet · Tampa, FL

Proven onthe rollers.

Our Dynojet 424xLC2 is an all-wheel-drive, load-controlled chassis dyno. We hold your car at any RPM and load to calibrate, test and diagnose under real conditions instead of guessing on the street.

Authorized COBB dealerSubaru AWD specialistsPricing up front
On the rollers
Model
Dynojet 424xLC2AWD and 2WD testing on two independent drums
Capacity
2,000 hp · 200 mphMeasurement range, 1,600 hp absorption in AWD
Load control
Eddy-currentDual absorbers for steady-state tuning at any RPM and load
Telemetry
AFR · boost · logsWideband AFR, boost, and OBD / COBB Accessport logging
Why load control matters

More than WOT pulls

A pull shows peak numbers. Holding RPM and load is how a car gets tuned for the way it is actually driven.

An inertia dyno measures a sweep. Ours holds the car at a fixed RPM and load, cell by cell, so every part of the map is set on data instead of street guesses.

DrivabilityPart-throttle and cruise cells calibrated under steady load, so the car drives clean in traffic, not just at redline.
Boost controlSpool, targets and wastegate behavior set while the dyno holds load, gear after gear.
ReliabilityTiming, fueling and temperatures checked under sustained load before the car sees the street.
RepeatabilitySame dyno, same procedure, every session. Before and after numbers you can compare.
Transparent session pricing

Know the cost first

Dyno time is $250 per hour with a one-hour minimum. Pick the session that fits and book it directly.

Baseline pulls

Power check

$2501 hour
1 hour session

Three baseline pulls with printed and digital horsepower, torque and AFR graphs.

Book power check
93 octane

Pump gas tune

~$500est.
About 2 hours

Full custom COBB Accessport calibration on 93 for bolt-on or built setups.

Book 93 tune
Flex fuel / E85

Flex fuel tune

~$750est.
About 3 hours

Dual-fuel mapping, cold start verification and ethanol content scaling.

Book flex tune
By the hour

Rental & diagnostics

$250/ hour
1 hour minimum

Controlled troubleshooting, boost leak verification, or dyno rental for a third-party tuner.

Book dyno time

Tune estimates are dyno time at $250/hr. We confirm your quote before the session; parts and repairs are quoted separately.

What you leave with

Real data, on paper

Dyno sheet · layoutPowerTorqueAFR
30004000500060007000RPMHP / TQAFR
Illustration of the sheet layout. Your sheet shows your car’s actual runs.
  • Wheel horsepower and torque across the RPM range
  • Air/fuel ratio logged on every pull
  • Before and after runs overlaid on tune sessions
  • Printed sheet plus digital copy
  • Run files and logs reviewed with you
The session

What happens on the dyno

  1. Inspection & strap-down

    Fluid check, tire pressure verification, four-point tie-down and sensor hookup for wideband and boost.

  2. Steady-state & WOT calibration

    Part-throttle drivability mapping using load control, followed by progressive full-throttle pulls.

  3. Cool-down & data handoff

    Post-pull heat soak check, final log review, and your printed and digital dyno sheets.

Before you strap down

Arrive dyno-ready

An unready car burns paid dyno time. Run through this list before your session.

Mechanical readiness

  • Fresh oil change
  • Zero fluid leaks: oil, coolant, transmission, differentials
  • Healthy spark plugs

Tires & alignment

  • Matched tire sizes and tread depth, critical on Subaru AWD
  • Proper inflation
  • No corded or damaged tires

Fuel

  • The fuel you want tuned already in the tank
  • Tuning 93 first? Don’t arrive on E85
  • Enough fuel for the full session

Tuning hardware

  • COBB Accessport unmarried, or married to this car, and working
  • Accessport cable
  • Functioning wideband O2 sensor if the car has one

Pre-dyno inspection. Mico Motorsports performs a safety check before strapping any car down. Mechanical issues found on the rollers are billed at standard shop labor rates.

Full specification

The machine

Published Dynojet specifications for the 424xLC2 on our floor.

Two independent drums, one per axle, each with its own eddy-current absorber. The dyno drives the front and rear together, so the Subaru AWD system and center differential work the way they do on the road.

Model
Dynojet 424xLC2 chassis dynamometer
Drive
All-wheel drive or two-wheel drive, 24 in drums
Load control
Two eddy-current absorbers, one per axle
Power
Measures up to 2,000 hp and 2,000 lb-ft; 1,600 hp absorption in AWD
Speed
Up to 200 mph roll speed
Axle weight
Up to 3,000 lb per axle
Wheelbase
88 to 130 in, adjusted electronically
Readout
Horsepower and torque at each axle, separately or combined
Test modes
Sweep, steady state, step and road load
Software
Dynojet Power Core with WinPEP 8 run files
Accuracy
Drum speed to 1/100 mph, engine speed to 1/10 rpm
Questions

Dyno FAQ

Will my car fit on the dyno?

Most cars do. The dyno runs all-wheel drive and two-wheel drive, wheelbases from 88 to 130 inches, and up to 3,000 lb per axle. Very low cars, wide-body kits or unusual setups: call us first and we will tell you straight.

Is it safe to put an AWD Subaru on a dyno?

On the right dyno, yes. Ours drives both axles at the same time, so the center differential and AWD system work the way they do on the road. Matched tires matter for the same reason.

Why are my numbers different from another shop’s?

Every dyno reads differently, and weather, fuel, heat soak and strapping all change results. Compare runs from the same dyno. The best use of a dyno is the change between before and after, which is exactly what we show you.

How long does a session take?

A power check is one hour. A tune on 93 octane usually takes about two hours, and flex fuel about three. If a car needs more time, we talk to you before going over the estimate.

What if something is wrong with my car?

We do a safety check before any car is strapped down. Mechanical issues found on the rollers are billed at standard shop labor rates, and we stop and talk to you before any repair.

Can I bring my own tuner?

Yes. Dyno rental is $250 per hour with a one-hour minimum, and our staff operates the dyno during the session.

Can I watch?

Yes, from the designated viewing area. Nobody goes near the rollers or straps while the car is running, and everyone present signs the dyno waiver.

Multi-map, race gas or something custom?

Call (656) 223-3113 and we will scope the session and quote it before you book.

Book dyno time

Reserve your session

Fill in the setup and goal. Your choices go into the message automatically, and we reply to confirm the time and the quote.

Session
Fuel type
Drivetrain
Transmission
Preferred days
Estimated dyno time$250
1 hour at $250/hr

Your details

Put the year and model in Vehicle Make & Model. Everything you picked on the left is already in the message.

Book dyno time

Get it on the rollers.

Tell us the year and model, engine and turbo setup, fuel and goal. We confirm the time and the quote.